Fleet-engineers INS-97005 Bedienungsanleitung PDF herunterladen (Seite 1)

STEP 2:

Headroom

Clearance -

Measure headroom

to be sure there is

sufﬁcient clearance to

accept the counterbal-

ance and to allow the

door to clear under the

roof bows (Figure 2A).

Use the chart in Figure

2B to determine the

required headroom for

your particular installa-

tion. Keep in mind that

whatever you add must

be ﬂush with the inside

of the side post.

Note: Figure 2A shows

the counter-balance

against roof skin.

Roll-Up Door

Installation Instructions

Installation Sheet #INS-97005

Installation Sheet # INS-97005 • Rev A 2/98 • Rev B 6/08

STEP 1

Check the door parts to make sure you have received all needed

items. Note any shortages or damages on delivery receipt as Fleet

Engineers cannot be responsible for parts lost or damaged in

shipment.

Figure 1

1. Hardware box - fasteners, rollers, cables, hinges, top ﬁxtures.

2. Counterbalance spring assembly with drums, shaft & bracket(s).

3. Pair of horizontal tracks.

4. Pair of vertical track assemblies.

5. Header seal and retainer or head seal on top panel.

6. Two door halves.

7. Side seals - optional on 3/4 door.

BEFORE PROCEEDING WITH THE INSTALLATION READ

EACH STEP AND SEE SAFETY NOTICE INSTRUCTIONS.

IMPORTANT!

Figure 2A

Figure 1

STEP 3: Sideroom Clearance

The minimum sideroom clearance is 2-1/2” on each side from the

post (opening) to the wall. Figure 3.

In the event it is necessary to add on the corner post, keep the

added piece ﬂush with the inside of the header.

Figure 3

Figure 2B

A B C D E

3/4” Doors 7” 5” 18” 2-1/2” 1-1/2”

STEP 4: Measuring Door Opening

Because each Fleet Engineers door is custom made, it is neces-

sary to check the opening measurement. These measurements

must be ﬁnished opening width and height. “Finished” means

there must be the header and side room clearance mentioned in

previous steps to insure proper installation.

Opening height is from the header to the sill, Figure 2A. Opening

width is from post to post, Figure 3. On older units, measure-

ments should be taken in at least three different places for open-

ing width and height. Cutting back of the ﬂoor on older units may

be necessary to permit the door to sit on the sill, below the ﬂoor.

See “D” dimension and chart in Figure 2B.

STEP 5: Vertical Track Installation

Position vertical tracks on corner posts as shown in Figure 3 and

clamp in place. Notch in mounting angle should line up with the

bottom of header (Figure 2A). If necessary, the bottom of the

vertical track assemblies may be cut off to permit the notch to line

up with the underside of the header. Keep both tracks the same

length.

1 2 3 4 5

Inhaltsverzeichnis

Seite 1 - Installation Instructions

STEP 2: Headroom Clearance -Measure headroom to be sure there is sufﬁcient clearance to accept the counterbal-ance and to allow the door to clear un

Seite 2 - IMPORTANT!

CAUTION!The vertical track assembly may be raised a maximum of 1/2” off the sill. Keep both vertical tracks the same length and same distance off sill

Seite 3 - WARNING!

PRE-WOUND COUN-TERBALANCE: If door is equipped with a pre-wound counter-balance, disregard above instructions and release spring tension as follows: C

Seite 4

door opening measurementsNOTE: Measure opening width & height at two different locations for comparisondoor installation tolerancesmaximum securi

Seite 5 - Headroom clearance

Wall-to-Wall standard referencesHeadroom clearance

Kommentare zu diesen Handbüchern

Keine Kommentare

Fleet-engineers INS-97005 Bedienungsanleitung Seite 1

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Hardware Fleet-engineers INS-97005 herunter. Fleet Engineers INS-97005 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Fleet-engineers INS-97005 Bedienungsanleitung Seite 1

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Hardware Fleet-engineers INS-97005 herunter. Fleet Engineers INS-97005 User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Hardware Fleet-engineers INS-97005